Broke down after 2yrs - Expensive to fix
We purchased this just over 2yrs ago and all of a sudden, stopped working. Took it to the repair shop - $800 for the motor + another $300 for parts and labour. The cord tangles regularly and the lid is difficult to open. It is also heavy to pull out of the water. I would not buy thin again. After sales service in Perth were less than helpful. Didn't climb the walls very well either.
Wouldn’t buy another one
We’ve had ours for about 2.5years. Stopped working after a month, and had to have it replaced. Worked well for about 6 months then had to bring it back. They replaced the external cables. It stops working for no reason and then will start again after afew days. We have a square pool, and constantly gets stuck in corners or on steps. Spent about $150 getting the tracks replaced because they kept coming off. That still happens and pushes the trap door clips open, so when I take it out of the pool, all the crap falls out the bottom back into the pool. For $1500 spent, I expected it would last 5 years..... going to have to replace it over the holidays. Not a happy customer
Great until it all went wrong
Worked brilliantly for about 1.5 years then went wrong so stopped cleaning the floor and just gets stuck in 1 corner of the pool. Took it in under warranty claim to be told because the retailer changed hand, it is not covered. $700 to repair or $1400 for new with $200 back for trading it in. No thanks! Tigershark seems to refer to the hayward attitude to customers as well as being the product name.
When it was working it was great - picked up heaps of leaves as well as gumnuts and liqid amber seeds. The terrible service now has put me off. A...s another user mentioned, pebblecrete takes a heavy toll as does the sun (to be expected). Hose kinks but changing the handle before I put it back in the pool each time helps. Advice to anyone buying it: Ignore warranty, budget for 1.5 years use then replace. Keep it out of the sun and clean filter after use. When on, allow to do its thing - when it was working properly, it was very effective.
Find out how Hayward TigerShark compares to other Robotic Pool Cleaners
Know better, choose better.
3 years life
Have had a tiger shark for 3 years. Excellent at cleaning even heavy deposits of gum leaves after storm events.
However, this is outweighed by the deterioration of the cleaner over the 3 years to the extent it now needs replacing.
The rubber drive belts have broken twice, the lower body on each side has worn through due to rubbing on the pool wall when cleaning in the corners. This has caused the fixing bolts of the rotating traction rollers to come loose.
The first time it happened it was just out of warranty but Hayward fixed under w...arranty but the second time with no warranty I had to attach a 6mm strip of HDPE to each side of the cleaner to secure the traction rollers and protect the plastic sides from wearing away. This has worked but the cleaner has just worn out and its time for a new one which will not be a Tiger Shark. If you have a square pool with pebble finish it acts like sand paper on the body of the cleaner so I am on the hunt for cleaner with side protection which I may have to add myself.
Questions & Answers
My shark is about 6-7 years old. A few weeks ago, when I start it , it runs for a few seconds and stops. After starting it two or three times it would finally keep going for the entire cycle. Now I have tried about fifteen times and it will only run for a few seconds and stop. What's up? Thanks
Very sorry C in Sumter, but I have not experienced that problem. Its possible some small leakage may have occurred in the motor/control housing. You will most likely have to go to the people you purchased it form or directly to TS as I don't recommend opening that unit.
The bottom cover keeps coming loose and all the debris it picked up falls to the bottom of the pool. Very poor design. Do you have any ideas to eliminate this problem ? Maybe something to wedge under the clip
my Tigershark (TS)seem to struggle to climb my step/ledge that runs the length of my pool and into a shallow area that is still deep enough to cover the tiger shark with water. The TS is completely cleaned out so not too heavy to climb and has had this issue since we purchased last December. Is there a way to fix this?
Well, I have to ask, did you check back with the pool shop that you bought it from?
In the meantime, there are a couple of ways of adjusting the water flow through the machine.
Both described in the manual.
The 1st is the restrictor plate on top of the machine. If the machine does not climb, removing it may help.
Next we have the "high velocity inlet". having this in place increases the velocity across the gap, so the suction is greater, but the volume of water is decreased.
So hard to predict if this will help. No harm in trying with it installed or not.
I have found that running the machine for 4 hours gives best results (rather than 2 lots of 2 hours).
|Category||Robotic Pool Cleaners||Robotic Pool Cleaners|
|Release date||Sept 2010|
|Replaced by||Hayward TigerShark QC|
- GTIN13: 0610377061339
ProductReview.com.au has affiliate partnerships. These do not influence our content moderation policies in any way, though ProductReview.com.au may earn commissions for products/services purchased via affiliate links.