Simpson SWT704 Questions & Answers
Verified
My machine I out of balance, shakes hard out on spin even with no clothes. I notice the plastic clips at the bottom of suspension rods are broken so rid just hangs
Simpson washer SWT704. Power ON-beeps. No lights. Press START in SPIN setting-pump runs-no lights. What is the problem?Thanks Bernie
how to remove the top to a ezi set7.5 kilo
Machine unbalance on spin cycle
Hello i have a swt704 and it seems to be stuck in pause it just refuses to start. Time flashes can chnage level temp etc
Hi Luke G, Tania from Electrolux here. We are sorry to hear you are experiencing problems with your Simpson washing machine. If you wish to discuss this further please feel free to contact me at customercare@electrolux.com.au attention Tania. Please list ticket number 4591692 in the subject line Thanks, Tania
how to remove control knob from Simpson washing machine
How can I tell if motherboard needs replacing
My Simpson Model SWT704 leaks water once the wash cycle starts and when I say leak it floods the laundry if left going
Hi any idea I keep coming across swollen 4.7uf,400v and 470uf35v on the board causing unit go off after few seconds of start up?
Please help me my washing machine Swt704 not rinsing and daring I already checked the water pump it’s alright and else I have to check.please advice
How to replace a lid for a Simpson EZI Set 9.5kg
How to replace lid
Where is the fuse located?
Simpson SWT704 EZIset No AC power or lights on the control board.
Very Common fault with this washer. The power supply in the control board often burns out. If you un-plug machine (important!) and take apart the rear control panel with all the controls- start with 2 (or 4) screws at rear - then you can often see the burn marks on the back of the printed circuit board. Replacing the controller board costs about $120-160 (look at Ebay) - the repair is easy to do and should last a while. Note - this is a major design flaw with these machines - Even with the machine switched off - the power supply inside remains powered on 24/7. You need to switch off the mains switch at the wall to properly power down the circuitry. I have fixed 6 of these faults.
I have experienced swollen electrolytic capacitors 4.7or,400v,470uf,35v any idea what's causing it.. Machines goes dead after few sections of start up.
My Simpson ez set swt704 gets to the drain stage then display comes up with e20
no power to my washing machine
was doing a load of washing yesterday and all of a sudden no power to the panel .
Hi Owen It’ll be the PCB behind the selection knob. The power connects through there. I had a burnt out card previously. Just google the washers model number and find the spare part. Easy to change. It’s a bucket of crap of a machine. Mine keeps beeping up error but continues washing. I’ve also paid a tech to replaced the suspension rods. It gets out of balance really easy again and it’ll be a matter of time before one breaks again.
Why are my clothes fluffy. Ive cleared filter and rinsed bowl but everything comes out fluffy
Its a swt1043
Good morning Netty, I would suggest that you clean the filter that fits into the top of the agitator and then check the agitator carefully for damage and rough spots that will cause this problem.
My simpson washing machine has no power model SWT704
Not sure if you received an answer, but mine did the same. Unplug the power from the wall. Remove the 4 screws that hold the display panel, and take the Power Control Board over to a local Simpsons parts supplier ($49.50) for a new one. Power restored. You can get it cheaper from ebay, but delivery is like up to 2 weeks. The PCB is the one that has about 3 or 4 plugs attached onto it.
my simpson washing machine model swt704 won't stay on what could be the problem?
Hello Phill, there are two items that I may suggest that could be your problem. The first is the cutout switch that stops the machine when you lift the lid. It is situated up under the left hand rear hinge. When the machine is running you could try lifting the lid. If the machine stops when the lid is a tiny bit open it would indicate that it could need attention. The other problem that we had with our machine is that we had to replace the control panel when it was only a few months old.
Get an answer from our members and Simpson representatives
Extra Information
ProductReview.com.au has affiliate partnerships. These do not influence our content moderation policies in any way, though ProductReview.com.au may earn commissions for products/services purchased via affiliate links.