Sphere 3.3kg Automatic Mini Washing Machine Questions & Answers
MPN: 700-00362
How do you replace safety lid switch on sphere 3.3 kg washing machine
You will have to lift the machine out to lift the entire top shroud off the machine, starting with the screws at the back of the machine. Be careful lifting it off, because there are heaps of wires from the control panel and the safety switch can get caught. Our first machine broke a safety switch after only 18 months of use and was out its 12 months warranty. We were camped up at Mataranka Springs NT at the time and the cost of freight just to get a safety switch sent to us was the same as getting an entire new machine sent, so we decided to replace the entire machine to get a new warranty. The second machine only lasted 14 months and also out of warranty, when the control panel gave up working. We are on our third Sphere 3.3kg washing machine now and it`s 18 months old and touch wood, no problem so far. Good luck :)
I have a sphere 3.3 mini auto in our van it’s about 5-5 yrs old I am getting a leak of water around the seam towards the bottom section of external casing can’t see where it is coming from could it be the pump
Have te Sphere 3.3 and when in spin cycle it gets very noisy, sound like a bearing is going, can the bearing be replaced, regreased or will we need to replace the machine.
How do we replace the lid and spring on our sphere 3kg washing machine.
How do we replace the lid and spring on our sphere 3kg washing machine
Hi I have the 3 3kg sphere I can do one load then on the next load it comes up C1 then does a 2 minute wash any suggestions to get rid of C1 mode thanks
We have just finished washing and have now turned off the water and power to the machine. However it keeps trying to spin. I don’t how this is possible without power. We just get this surge noise every 30 secs approx. Has anyone suffered the same issue?
I have a brand new sphere washing machine, day one 2 washes , started wash number 3 and now dead ! No faults ! You need power to show a fault and yes it is plugged in ! I’ve done all the troubleshooting and it’s dead , junk !
That is exactly what happened to ours. I pulled it apart trying to trace the problem but that didn’t help. I think it is the controller board that fails. They are rubbish.
Just had the same. Just died, no fault message no nothing. Just dead after 2 years. Did all the trouble shooting as well. But just dead. This is the second heap of junk in this van. The last one lasted 18months before it gave up the ghost.
I have one of these fitted to our StarCraft , on Spin it thumps around and makes a terrible noise, it’s our third Machine supplied by Sphere under warranty, I videoed it spinning to Sphere and they replaced it at there cost. Current machine is horrendous with out of balance and noise. Am I the ONLY one with this bad luck?, original machine was a 2.5 lasted 7 years never missed a beat, till the motor spat the dummy.
It seems the 3.5 are crap straight out the box.
My SPHERE 700-00362, 3.3.kgm mini fully automatic washing machine has a lint filter. But it does precisely nothing. A previous LEMAIR machine, had a brilliant filter that was exceptionally effective. Do I need to adjust something?
Has anyone had the F1 error code and solved the problem?
Brand new Atlantic van with obviously, a brand new Sphere 3.3kg washing machine. Manual states a 2-3.3kg wash with high water level will use about 26 litres of water. Tested it out and it used 70 litres?? Can anyone explain? If that's normal we will never use it. I have spoken with Atlantic and they have not head of it before and are making enquiries. Thought I'd ask those that have one. Regards Gerard
The 26 litres is for each cycle: wash, rinse, and final rinse--TOTAL of about 78 litres (3 x 26).
Hi our sphere W/M washes and pumps water out but either spins very slow or not at all.Any ideas as to the problem.Its 2yrs old.
Hi my machine is exactly the same after 2 years, looking forward to some feedback.
I have a sphere 3.3kg washing machine in my van and the agitator stoppped moving any ideas on how to fix it
The Sphere washing mcahine in my Starcraft trips the power when it gets halfway through the spin cycle. I have tried running it with and without a load and from different power supplies. Has anyone else had this issue? if so how did you rectify it?
Wayne, sounds like either the machine has a large fault or your power breaker is under rated, you need a electrician to put a clamp test on the power lead when running to find if it is the machine or breaker. Glen
Hi Glen,
Thanks for the information I will reach out to my local electrician.
My sphere 3kg won't empty , has E4 error code ?
Hey Rob did you get this sorted? Mine is doing the same
Yep needed a new control board ,and a little bit of tweaking the colour coded wires were different
My 3kgSpere won't spin , showing E4 , what does it mean , and how to fix it please
Need help. The push down start/pause button does not work. It appears as if there is nothing under the top covering. All other buttons work. Machine works well when I can get the button to connect. It appears to be a stuck down panel.
We have never used our new machine and when we turn on it and select our setting there is no water water starting to come through any ideas why?
I know this sounds silly but is the shut off tap in the van for the machine turned on?
My sphere washing machine will not spin. Whats the fix.
Get an answer from our members
Extra Information
ProductReview.com.au has affiliate partnerships. These do not influence our content moderation policies in any way, though ProductReview.com.au may earn commissions for products/services purchased via affiliate links.