??!
4 photos
Ryobi 26cc 2 Stroke RLT26CDSN

Ryobi 26cc 2 Stroke RLT26CDSN Questions & Answers

MPN: RLT26CDSN
1.7 from 33 reviews

11 questions from our users

Hendrico P.

Hendrico P.asked

My 26cc Ryobi trimmer won't start. I replaced the sparkplug. What must I do further?

No answers
Shaun

Shaunasked

My spark plug was jumping Spark to the rubber so I pulled the rubber off and there's another wire in there what is that used for cos now I can't get spark on the spark plug properly

No answers
Stephen E.

Stephen E.asked

Is there a fuel mixture screw

No answers
Stephen E.

Stephen E.asked

Fuel mixture screw

No answers
Doug

Dougasked

Where can I get an exhaust for one of these?

No answers
holdom

holdomasked

The shaft to the end of the line trimmer will not turn ,with motor going. Any ideas?

2 answers
DAVIDB
DAVIDB

Bin it.

Craig
Craig

I had the same problem occasionally. I had to stop “revving” it and give the head a tap on the ground to see if it would turn. When it finally engages, add power. Good luck. Very annoying bit of kit.

Harry

Harryasked

Hi where do I buy a new head for my RLT26cdsn grass cutter? I don't want to be caught again as inthe past where sales people tell you this 1 will fit yer right Thankyou.

2 answers
DAVIDB
DAVIDB

Personally I recommend putting the thing in the bin. Search Bunnings Ryobi line trimmer accessories they have what you need.

MyCozyHome
MyCozyHome

Hey Harry...
https://www.bunnings.com.au/ryobi-2-4mm-x-6m-reel-easy-line-trimmer-head_p3380130
This should be the one you need. Just make sure you use the yellow knob to tighten the head on completely (it has a "wrench" built into the inside")

Then once it is installed... line up the line with the arrows, and fish the line through the middle ... and wind the knob.

Good luck!

Tricky

Trickyasked

Having trouble with line will not feed and have to pull apart every couple of minutes to re-thread which way should line be coiled anti clockwise or clockwise?

2 answers
Phil C
Phil C

Hi Tricky, Sorry for the delay in replying. Haven't checked my email for a while. One of the endearing features of the Ryobi line trimmer is that it uses the same spool for straight shaft and bent shaft trimmers. If you take the spool off to clean it and put it in upside down the line winds in not out when you bump the head. If you look closely you will see print on the spool saying something like "This side out straight shaft line trimmers" and the other side has "This side out bent shaft trimmers. Try flipping the spool and see if this helps. The other problem I have had when really working the trimmer hard is that the line can melt onto the spool. I don't know a fix for that problem. Good Luck. Phil

Tricky
Tricky

Thanks for your reply

Mike

Mikeasked

Ryobi line trimmer 25.4cc c/shaft RlT254FCDSN have tried new spark plug, new lot of petrol, cleaned filters still doesn't fire up only floods with fuel. Any suggestions. Second time used since purchasing. 07/02/2015

1 answer
Phil C
Phil C

Hi Mike, Sorry for the delay in replying. Are you getting a spark? I ended up buying a new carby for mine on line, which cost about $30. It's working again, but it wasn't that easy to change. Could be oil built up in the cylinder if you haven't used it much. You may be able to rinse it out by putting clean petrol in the spark plug hole and rinsing it out. Otherwise I'd suggest getting someone to look at it.

Boone

Booneasked

Above Ryobi starts but once you apply trigger pressure just dies there is a very small rubber washer which has started to perish so it sucks in air trying to find someone who sells this still scratching my head any ideas?

2 answers
Peter
Peter

My best advice after going through 3 Ryobi's 6 months (all under warranty) is take it back get a refund and buy a Weedeater (they are actually made by Husqvana)

Boone
Boone

My ryobi is 3 years old But has only been used 4 times but still you are right this model is CRAP I will write to Ryobi and hopefully get something in return it was originally bought from bunnies would you know the address of ryobi to send letter

renee

reneeasked

How do I thread the cord?

1 answer
Jess
Jess

This particular model comes with an easy feed bump head. Line up the arrows with the line (ensure the spool has 'curved shaft' facing up).
Feed up to 6metres of 2.4mm line right though the middle, then wind back in.

Get an answer from our members and Ryobi representatives

ProductReview.com.au has affiliate partnerships. These do not influence our content moderation policies in any way, though ProductReview.com.au may earn commissions for products/services purchased via affiliate links.