Bosch VeroBar 100 TES70129RP Questions & Answers

Hi Zia, it's been a very long time since I owned one of these machines, but I seem to remember that grind adjustment was from inside of the bean hopper. You should find a small knob in there for adjusting grind size. How this helps.

Hi there, I don't have the same model as you so I'm afraid I can't help. Perhaps call Bosch technical support for help.

Hi Elvina, Thanks for your question regarding the Bosch TES70129RP. As per your user manual the power button is the top left of the control panel. If you're wanting to do a factory reset: Hold down the up and down buttons and the on/off switch at the same time for at least 5 seconds. Press the start button. The factory settings are now reactivated. If you need any more help, feel free to contact us on 1300 369 744. Regards, Bosch Home Australia

Hi Amen, Thanks for the question regarding your Bosch TES70129RP. Based on sensors in the appliance you would need to clean and fill the water tank. Based on the user manual, if you were in the middle of the Calc'n'Clean you would need to then press the start button to continue the process. If you've done this and the message continues a service may be needed. If you need any more help, feel free to contact us on 1300 369 744. Regards, Bosch Home Australia

Thank you so much that was helpful.

Hi Patrick L, Thanks for your review, we appreciate the feedback. We're sorry to hear that you're having issues with your Coffee Machine. You may need to descale your appliance. We'd like to help, if you contact us on 1300 369 744 well investigate for you. Regards, Bosch Home Australia.

Thanks for the response. We descaled but still no response from the coffee spouts. We think the motor or circuit driving the coffee has packed up. We are sending the machine in to Bosch South Africa for a service.

Hi Patrick, we are having this exact problem with our same machine. Did you manage to have it fixed at Bosch SA and was it a big, expensive problem? Wondering if time for an upgrade (as have replaced circuit board before). TIA. Christina.

Hi benjamin, Thanks for the question regarding your Bosch TES70129RP. There is nothing we can recommend other than a clean and descale. If you have tried this, a local coffee machine service technician would be able to help further. If you need any more help, feel free to contact us on 1300 369 744. Regards, Bosch Home Australia

Hi Leanne. My only advise would be to thoroughly clean the unit, especially the water side of things (run cleaning program using good quality coffee machine cleaning solution). Clean the make and female parts of the frother where it connects onto the machine. Then refit using the food grade grease that comes with your verobar. This will help to create a good seal and better stream pressure. Good luck!

Hi Wessel V, Thanks for the question regarding your Bosch coffee machine, The power switch is used to switch the appliance to “energy saving mode” or to switch it off completely. Please note when in “energy saving mode” only the button 2 lights up. Do not switch the appliance off at the power on/off switch until it is in energy saving mode, so that the automatic rinse process can take place. If you need any more help, feel free to contact us on 1300 369 744.  Regards, Bosch Home Australia

Hi Charles, thanks for your question. We'd like to help you investigate, if you could please contact us on 1300 369 744 to discuss. Regards, Bosch Home Australia.

I never had this issue with mine, though I have heard it hapening for the main water tank saying it needs to be refilled. I would go looking for the sensor that detects the water in the drip tray and clean and check it for function. Other then that, I can only suggest contacting Bosch directly. They are generally pretty good responding to requests for help. Sorry I could not be of more help.

Hi Totalalkhiam,

Thanks for your question regarding your Bosch TES70129RP coffee machine.

Please contact us on 1300 369 744 to discuss further.

Regards, Bosch Home Australia.

Probably up to 1/3 a cup. I need to empty the tray every 6-7 mugs made and it would carry about 3 cups.

I concur with Joanne but would suggest it is only about four cups, but with the brew head rince and frother flush, it requires emptying every morning before making your cup. The machine will not allow you to make a coffee before you do this.

Thanks very much, I was concerned we had a leak but it sounds correct.

Hi Eli, is the magnet in the side of the water tank moving freely? It may be stuck at the empty position and this would tell the machine that the tank is empty, even though you have filled it. This has not happened to me...yet! But if it did, I would try gently to tap the housing around the magnet to get it to move up and down. If this doesn't work, it must be either an electrical fault within the machine body and would require specialist attention. Hope this helps.

Hi Matt, Thank you very much for your suggestion, I don't have magnet on either the tank or the machine its a spring control valve on the bottom of water tank which sits into the machine where water is drawn as required, I cleaned all these but still same problem, the unit is hardly used so not sure if its an electronic issue?

Eli, the magnet Matt is referring to is the disc that that is contained in the wall of the water tank, near the bottom in the middle of the back wall that is concealed by the machine when the tank is in place. It moves up and down only a few centimetres and it acts as a level indicator for the machine to know it has the minimum water level. If you take the water tank off and turn it upside down, you should see it move and hear it 'clonk', if it doesn't this may be your issue as Matt has indicated. If not, try turning the machine off and unplugging from the wall for a minute, then plug in and turn on - basically a 'reset' in case it's a software glitch. Failing this and any advice from the manual, you probably need to contact Bosch about it.

I haven't had this problem, so failing consulting the manual and making sure the cleans and descales of the machine are up to date, you should contact Bosch to see if there is an easy fix for this.

Hi Linda, Sorry to hear you are having troubles with the brewing head. Unfortunately I have no idea how to remove those nozzles or if indeed they are removable. On close inspection of the actual drippers on the bottom of the chrome nozzles, they look as if they could be undone with the appropriate tool. You could first try soaking the nozzles with some descaling solution in a container set up to immerce the nozzles? Also maybe scrub them with the same solution. My cousin has an older Bosch machine and he said he regularly needs to clean the nozzles to keep them flowing properly. Fortunately mine are working properly far, unlike some of its other functions. Im shocked by how often it asks me to clean the brewing unit, which only happens half way through making a coffee! Any tips on how to do this properly would be appreciated! Good luck!

Matt.

Hello Linda, I haven't had this issue and if the manual doesn't help with this, then the best thing to do would be to contact Bosch about it. Joanne.

How do you dismantle the nozzle section from the machine to clean it. Any videos to show how?

Hi Linda, Thankyou for your question. If you are unable to find these instructions in your user manual, please contact us directly for assistance and troubleshooting on 1300 369 744, be sure you have your model number ready. Kind Regards, Bosch Home Australia

Hi Борис Ђорђа Маркуш , Thanks for your question. We're sorry to hear that you're having issues with your Bosch TES70129RP. We'd like to help you investigate, so could you please contact us on 1300 369 744 to discuss further. Regards, Bosch Home Australia.

Failing any help from the manual, you should contact Bosch about it.

Hi Grant, Thanks for your question. We're sorry to hear that you're having issues with your Bosch TES70129RP. We'd like to help you investigate, so could you please contact our After Sales Support team on 1300 369 744 to discuss further.

Regards, BoschHomeAu

Hi i got Bosch Vero bar 300 and i replaced Voter pump after everything vas finished and i fill the weather thank turn machine on and after that always vas asking "Fill the water tank". Is it maybe air in the house ???and if it's how to fix that problem.