Bosch PSR 14.4 LI-2 / 18 LI-2 / 18 LI Questions & Answers
Verified
I need a new chuck it has jamed pulled it apart the part I need is the thechuck which is in front of the 2 speed gearbox or gearbox and chuck unit is it possible to get part
my Bosch drill PSR-Li2 drill wont work with a new 4ah Bosch fully charged battery. It works well with a 2.5 ah battery. Any idea what the problem is?
My psr 18 l1-2 will not operate with a full battery, tried the batteries in another psr. The lights on the drill come on and flash 3 times then go off. This drill has had very little use and has not been overloaded, any suggestions please?
I was using my new 18v bosch battery drill in the rain (an emergency job) and it stopped working, no light, no life. Is there a fuse built in?
Where can I have minor repairs/Maintenance done to my BOSCH PSR !8 LI-2 ? Thanks .In AUSTRALIA, preferable West Australia. 6169
what is the price of this PSR 14.4 Ll-2 beauty?
Can the PSR charger charge the PSB battery?
chuck size
Can I use an 18volt Battery in my 14.4 drill?
HI there, the drill stopped earlier today so I put it to charge. The charger light blinked for sometime and shows steady now however when I put the battery back on the drill, it doesn't rotate. Moreover, none of the lights are glowing on the drill. If I put the battery on charger again, it blinks for a couple of minutes and then goes steady green again. Has the battery gone dead OR the drill, please help!
It sounds similar to the unresolved problem that I have.If you slide off the battery and partially depress the trigger and then slide the battery back onto the lock position will the drill start to spin ?
Graham - I've been trying to problem solve this problem for 24 hours and looking on YouTube and various forums. Without meaning to jinx it - your solution has worked for me. Thanks
Cheers Graham, I had same problem and came across your solution, it worked!
I have a psr14,4 Ll was working fine put the battery on charge and after charged I have no power at all,if I put battery and drill on charger and push trigger the light on drill flashes along with the 3 charge lights but nothing else can you help please?
Does the PSR 18 LI-2 use the same or a compatible battery as the original PSR 18 LI?
To answer my own question, yes it's compatible I find.
Are the batteries still available for this drill?
If you google the drill name and 'batteries' you will find them. You can still buy the drill.
My PSR 14.4 with fully charged battery will only work if you put it on charge for a few moments, and will not work after the trigger is released, until you repeat the procedure. Any help?
mate, take it back. We pay for a reliable product and you have a dud.
Selecting torque still slips when you reach 20 and can be stopped by your hand although you can tell the difference as you go up the scale! Any ideas. Malcolm
Hi, my PSB 18Li-2.....stopped working. The batteries are good, and charged. The 3 green lights and the white light flash 3 times, then nothing. Any clues? Is it an economic fix?
I have the same problem. But when i keep pulling the trigger several times it will work. When release the trigger it will go off and hard to turn on again. I need to press the trigger few times until run
I have the exact same problem. Did any of you find a solution?
Same problem
PSR 14.4 LI-2: inserted a new and fully charged battery pack, pressing Run button the device only flashes white LED once.
With previous battery everythin ok.
Any idea ?
NB: measured voltage on battery pack + to -
A: contacts towards device: old 16.4V, new 16.7V
B: contacts towards charger: old 14.3V, new 13.7V
I found the solution Resitantance between Minus and next contact versus Drill is currently 3.17 KOhm. Too less. Drill works with a rerstistor in Accu within range 3.2 to 3.4 KOhms. I will replace the resistor by one of 3.3 KOhm
Thanks for your attentions
My psr 18 l1-2 will not operate with a full battery, tried the batteries in another psr. The lights on the drill come on and flash 3 times then go off. This drill has had very little use and has not been overloaded, any suggestions please?
If this happens with both battery's, return it.
Dodgy unit.
My PSR18Li-2 burned out, when I pressed the trigger. Is there a an ability to by a 14,4 single. Otherwise I have to shift over to 18 Lo-2?
Where can I by a 14,4 single drill?
Dont think they sell singles in 14.4 probably best looking on ebay/ gumtree for second hand or upgrade.
What is maximum speed of PSR 18LI-2?
Max speed is 1340 rpm
Get an answer from our members and Bosch Power Tools representatives
ProductReview.com.au has affiliate partnerships. These do not influence our content moderation policies in any way, though ProductReview.com.au may earn commissions for products/services purchased via affiliate links.